Anker’s Ultra Slim Extended Battery Case provides the best blend of good performance, price to the capacity, and physical size (the amount of bulk it boosts the phone). It has the capability to supply 117 percent of a full charge to an iPhone 6 or 108 percent for an iPhone 6s. The cost tag, $40 around this writing, is crazy low for the battery case: At this rate, the Ultra Slim offers the best charge value (a 2.9 percent charge per dollar, or $34.34 to get a full charge, for your iPhone 6) of any one of the cases we tested, by far.
The Ultra Slim doesn’t offer an especially premium feel. That’s not saying it comes off as cheap, but nothing about its physical construction is particularly impressive next to other cases. Another minor strike against this Anker case is its lack of button coverage; we more often than not prefer (well-designed) press-through button covers that protect the iPhone’s various buttons and minimize the volume of places where dust and dirt could get below the iphone6 case supplier.
For the iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim for the iPhone 6 Plus or 6s Plus, so for anyone handsets, we like the Tylt Energi Sliding Power Case. Unlike most of the models we tested, this one includes a separate protective case that you can slide out from the battery sled if you don’t need the extra power, so that it is a far more-practical selection for the already huge Plus models. It’s another great source of energy, providing on average a 93 percent charge towards the iPhone 6s Plus in our tests.
A vital thing to keep in mind using the cases we dismiss below is because they will not be necessarily bad. Although we’re noting any issues we saw by using these cases, many of them are fine-they merely can’t quite match up to the good quality in our picks.
Our previous pick for the more protective case was Speck’s CandyShell. A perennial favorite, they have two layers of material-plastic externally, rubber internally-that supply more protection than case designs that happen to be just one or even the other. The CandyShell is 10.9 mm thick, which puts it on the chunky side, however it doesn’t feel exceptionally bulky, and it’s one from the only cases we tested that claim to satisfy military drop-test standards. Speck supplies the case in a wide range of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell carries a few conditions that keep it from becoming a top pick, though. For beginners, the CandyShell’s glossy back almost instantly attracts small scratches that generally aren’t visible directly but jump out when you look at the iPhone with an angle. Granted, these scratches don’t change the protection the case offers-and we’re naturally happier to view scratches around the case rather than around the phone itself-but it might be nice if Speck were to offer the case by using a matte finish.
The other issue is the case’s shape. A lot of our readers, in addition to a contingent of Amazon reviewers, take issue with the fact that the CandyShell’s back is slightly convex. Specifically, whenever you set the situation on the flat surface, this “hump” causes the truth to rock whenever you press along any kind of its edges, or perhaps to spin similar to a top should you push it. (When you got a new CandyShell and also you mind this spinning and rocking, Speck says to contact its customer care department.)
OnePlus (the Android phone maker) surprisingly decided to go into around the iPhone-case game having its Sandstone Case. The large draw is OnePlus’s Sandstone texture; TIME says that it “feels like smooth sandpaper” and that “[i]t’s super grippy, so that it is very difficult to drop.” Unfortunately the truth is a shell with open top and bottom edges, meaning it’s less protective when compared to a good case needs to be. Due to this design drawback, it fell out of competition.
SwitchEasy carries a mixed history, one which makes it difficult to tell the complete story depending on its cases alone. Its Numbers case was our original pick for that iPhone 5 and 5s, before a wave of reader complaints about quality and customer satisfaction. The answers we got from SwitchEasy weren’t thorough; mostly, the organization blamed the down sides on third-parties selling knockoffs of the products. (At iLounge, I discovered the SwitchEasy protectors to get impressive generally-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all of that in your mind, we looked at three SwitchEasy cases to the iPhone 6. The initial one is the Odyssey. Like a few of the better cases we’ve evaluated, it’s a mixture of plastic and rubber. Instead of being layered, the types of materials run side-by-side, with the hardened rubber making up many of the case. It isn’t the prettiest case, inside our opinion, but it is protective. It covers the buttons without reducing much of their clickiness, and six holes along the bottom line up precisely using the speaker vents. Our favorite part of the case may be the port protection: Rubber protectors squeeze into the headphone and Lightning ports, respectively, when they’re not being utilised, keeping dust and also other debris out.
SwitchEasy’s Tones includes a similar port protection and uses the identical materials. Your body is usually plastic, though, using the rubber walking around the edges like a border as well as across the rear of the way it is, matching the iPhone’s antenna lines. We’d prefer a layer of rubber between your handset and the plastic back of your TPU iphone6 case, and the Sleep/Wake button demands a bit an excessive amount of pressure on the number of units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we were prepared to name it as being our top pick-but there’s far more for the story than merely our review units, therefore we found a substantial fault after a little extended use. This situation is almost just like the Incipio NGP, however it offers more protection. As opposed to leaving the phone’s ports totally exposed, the way it is provides protectors that fit into the headphone-jack and Lightning-port openings to maintain dust and debris out. It’s a good touch that’s executed well. Even the phone’s speaker is way better protected, with six individual holes rather than one long opening. We actually much like the tactility in the devqpky94 a bit more with SwitchEasy’s model when compared with Incipio’s case, too. An early yellow version of your case we tested accumulated permanent stains, but later iterations exhibited no such issue. The problem is that the truth is a little too loose, so the corners disappear too easily. We experienced this concern over and over while eliminating the encased phone from the pockets. Because we’ve had other problems with SwitchEasy cases before, we’re still a little wary. If you do choose to get a SwitchEasy case, we recommend buying it directly from the company’s website. Doing so will eliminate any potential warranty difficulties with third-party sellers, if you have any issues with the situation.
An essential thing to keep in mind together with the cases we dismiss below is the fact, unlike along with other types of products we cover, they are certainly not necessarily bad. Although we’re noting any issues we saw with these cases, many of them are fine-they merely can’t quite match up towards the top quality of our own picks.
Combining a rubber skin with a plastic frame, the Spigen Neo Hybrid is a slim, attractive case. Its fatal flaw lies in its button protection. The silver plastic pill across the Sleep/Wake button doesn’t depress properly, so it may possibly not hit the control underneath, and you likely won’t feel it when it does. Former Sweethome editor Joel Johnson confirmed this matter using the iPhone 6 Plus version. Because we received this example for testing so early, we think Spigen might revise later editions to manage this concern.
Also from Spigen will be the Ultra Hybrid, an individual-piece case that fuses a rubber frame having a clear plastic back. It’s a nice-looking case, but once again, it provides complications with the buttons. As an alternative to putting raised material over them, they have left and right edges which can be flat from top to bottom with small indentations. For the Sleep/Wake button, the indented label says “PWR,” and then for volume, you receive plus and minus signs. Without having a more pronounced physical distinction, you may more quickly miss the buttons, and also the frame moves inward when you press.
Twelve South is in the beginning about exactly how protective the SurfacePad is. From the FAQ section of the case’s website, the corporation says, “SurfacePad for iPhone will not be made to protect iPhone from falls, drops, being run over by way of a car or dropped within the loo. SurfacePad is meant to guard your iPhone from scratches and scrapes from such things as car keys, nail files or concrete park benches.” It’s actually less of a case and more of your leather sticker with a cover. The SurfacePad adheres to the back of the iPhone, and you could eliminate it and reapply it as necessary (though accomplishing this will not be as elementary as the corporation might have you think). We like the type of material, however the SurfacePad is difficult to recommend unless your main problem is fashion.
The Vault Slim Wallet from Silk is a much-less-expensive replacement for sister company CM4’s Q Card Case. It’s essentially the same design, except instead of a faux-leather back, everything is made from TPU. Just like the Q Card Case, the Slim Wallet can take three cards, but an elevated arch within its card slot causes the cards to curve to a noticeable degree, which could damage the cards over time. The Q Card Case’s positive attributes otherwise carry over, but because of the card bending, I’m a bit wary of the Slim Wallet.
Silk now offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case is a rubber case with interchangeable, polycarbonate-plastic backplates. It’s a great case at a reasonable cost, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, however, is really a nice pick within the very full type of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly partial to this style as a result of dust’s propensity to have below the transparent back, as a result of the ease that the plastic can scratch. Still, alongside others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike with the NGP, merely the border is TPU; the other Rival is hard plastic, about .3 mm thicker than the NGP. Anything else regarding the case is essentially exactly like in the NGP, including the cutouts for your ports and the grade of the button protection. While the Rival is incredibly smooth, just like the NGP, horizontal lines across the lower two-thirds of their back give a distinct texture. It isn’t as neutral since the NGP, but if you appreciate the design and style, it really is a great choice.
Tech21’s Evo Mesh, which features the second generation of the company’s shock-absorbing lining, is an Apple Store exclusive. Very much like Tech21’s Classic Shell (more about this design below), it’s a rubber case having a colored band walking around the perimeter. The dimensions are virtually identical between the two. There’s something relating to this one that people like more than the Classic Shell, but it’s challenging to put a finger about what which is. Perhaps it’s that the somewhat-obnoxious orange band has been replaced by colors matching the different body shades in the case itself. Overall, though, this example is simply too pricey for which it offers you.
Plastic and rubber by using a clear back, the ITSKINS Venum Reloaded drops the ball in relation to within the iPhone’s buttons. Like the setup of Spigen’s Ultra Hybrid, the design from the Venum Reloaded makes hardly any physical distinction between the button coverage and all of those other case. This example was also relatively expensive when last we checked, along with the plastic border frame feels fragile.
Really a greater portion of a fashion case, the Nitro Forged from ITSKINS currently costs quite a penny at nearly $70. It is made up of rubber skin with machined aluminum caps that attach at the very top and bottom. Thankfully, this design is definitely an improvement over previous versions, which required you to definitely utilize an included screwdriver to install and take off the caps; instead, it uses small plastic clips you could devote and remove by hand.
Also from ITSKINS is definitely the Evolution. A rubber core having a plastic frame, the Evolution has some curves that will help ensure it is feel slightly more organic. The large problem is that the screen rises on top of the edge of the case rather than the opposite. Because of this in the event you drop your handset, there’s much more possibility of injury to the display compared to other cases.
Incipio makes so many cases we can’t expect great things away from every one. The Advantage can be a plastic slider, a style that’s relatively rare today. The smooth, matte-finish plastic splits into two pieces both for installation and docking purposes. While it offers proper button coverage as well as a nice protective lip, we found the situation being too tight; pulling it away, specially the bottom cap, is really a struggle.
Weighing several grams more than the normal of the cases we tested, the DualPro SHINE is a solid contender from Incipio. It incorporates both plastic and rubber layers, although as opposed to being molded together, they’re two distinct pieces. The rubber is rather thick but doesn’t dampen the tactility of the buttons by any means, and yes it still provides acceptable accessibility ports. The port openings are exactly like the NGP’s. We also checked out the standard DualPro, that features a matte finish. It’s quite nice, but it’s thicker compared to the NGP and lacking the mil-spec rating in the CandyShell.
The plastic layer of the DualPro SHINE fits into grooves within the rubber, helping the case think that a cohesive unit. We think by far the most polarizing thing about this case is its texture: Made to seem like brushed aluminum, it certainly doesn’t seem like that, and at least in your tests, the effect is a certain degree of cognitive dissonance. It’s not a bad thing by any means, but overall it really doesn’t feel as nice because it looks.
If card storage is vital for you, Verus’s Damda is a fine case. Your body consists of black rubber, with nice button protection and properly centered openings for your headphone port and microphone, the Lightning port, along with the speaker. Linked to the back is a plastic compartment that adds both mass and depth. A plastic door slides open to reveal space for a couple of, maybe three, bank cards. We initially thought it was a bit difficult to open, although with some cards within it’s easier to use yet still secure. This can be more of a niche case than our pick.
Verus’s Crystal Mixx offers a transparent window along with a rubber frame. The rear with this one is plastic, which can be one of these two drawbacks. In our exposure to iPhone cases, clear plastic scuffs easily and definately will show those scratches within a point of days. This example will not be so bad in case the frame provided a much better lip. Unfortunately, at .3 mm, it’s one from the shortest lips we saw, and it also may lead to problems in the event you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a good deal alike, with each model is difficult to acquire-Pelican doesn’t sell them online, as well as in our experience they’ve been reliably available only at AT&T retail shops. The Protector is really a bulkier, more-angular carry out the CandyShell design without any additional benefits, so we’d pass into it. The Voyager adds port protection and funnels the sound through the speakers forward. Additionally, it has a belt clip and screen film. We notice this model rather than an OtterBox case, as it’s basically overkill. A lot of people simply don’t need this degree of protection, especially not if they have to go out of their strategy for finding it.
PureGear’s Slim Shell Case can be purchased in seven color combinations, including clear-on-clear. This model is challenging plastic by using a rubberized but nevertheless rigid frame. The metal button covers certainly are a very nice addition, helping the case feel more premium. It won’t offer as much protection being a CandyShell, so it isn’t a top-notch pick, but this one isn’t a poor option at all.
One of the first iPhone 6 cases to get publicly sold-we saw it as soon as May 2014-Minisuit’s Frost is surely an inexpensive TPU skin. While it does fit, it has virtually no lip, along with the holes down the bottom are uneven to the point of looking warped.
Monoprice is acknowledged for inexpensive products of all sorts. We love to a few of the company’s accessories-it makes great cables, by way of example-but Monoprice cases generally don’t impress. Materials often feel cheap, along with other companies offer higher-quality products at similarly the best prices. For instance, the Metal Alloy Protective Case (offered in gold, silver, and cosmic blue) includes a thin, aluminum shell that snaps over a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice because the material that Incipio and also other companies use, and the case exposes the Apple logo on the rear of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels a bit nicer but is much less protective. The plastic shell has has a cool-looking steel grille over it, but it leaves the top and bottom edges unprotected, and yes it features the biggest Apple-logo opening we’ve seen on any case.
We examined the TPU case from Insignia, a Best Buy brand, and yes it is apparently through the same OEM as Monoprice’s TPU case, but with a higher price.
We don’t just like the Monoprice PC TPU Protector Case as much, although it does offer arguably more protection. This model splits into two pieces, having an inner skin of TPU as well as a polycarbonate shell that snaps in place over it. The truth is rather simple to assemble, but once it’s together, it simply feels big. It’s both wider and thicker compared to NGP, without having obvious advantage other than price.
Rokform has long dedicated to ruggedized cases that can connect to an ecosystem of mounting accessories. Its Sport v3 is not any exception. This plastic and rubber case incorporates swappable magnetic backplates that allow it to get connected to various mounting brackets the corporation sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” Nowadays the corporation claims that this magnet won’t obstruct Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series will be the bulkiest in the cases we’ve tested to date. This is actually the company’s flagship case, the one many people associate using the brand. It’s comprised of a plastic frame that snaps across the handset as well as a thick rubber skin that covers everything. Unlike many other cases, this model includes flaps over the vibration control switch, headphone port, and Lightning port-all positive things on an extra degree of protection. In addition, it includes button coverage, but we discovered that it requires more force to depress the quantity and power controls than other cases do.
The Defender Series is also the only real case we’ve tested with built in screen protection such as a specific film integrated into the frame. Since you end up with a little space between the protector along with the screen, very light presses and swipes might not exactly register, and that is a drawback. Atop the Touch ID/Home button is really a thin sheet of plastic that didn’t hinder the experience within our testing. Whilst the Defender Series does expose the Apple logo, the situation at the very least covers it with clear film that prevents it from getting scratched. So that as a bonus, the Defender Series features a belt holster.
From the OtterBox family, the Commuter Series represents the next step down in overall protection. As an alternative to plastic inside and rubber on the exterior, the layers are reversed. The truth still offers port coverage, but the switch about the iPhone’s left side remains exposed. Thankfully, the buttons depress a lot more easily. Rather than a permanent screen protector, OtterBox includes an optional film with this case. The Apple logo is once again exposed, this period without any plastic covering it. Other than the port protection, this situation offers no obvious benefits more than a CandyShell, along with the dimensions are a drawback that keeps this model from earning a top-notch spot.
The Symmetry Series is really a relatively recent addition to the OtterBox lineup along with the slimmest of these all. It is like a direct response to the CandyShell, having its dual-layer design. This case offers the same level of protection as our top choice plus a substantial lip. It’s taller and wider, though, at the higher price. The greatest benefit is using a matte-plastic back, it won’t show the scratches a CandyShell does.
OtterBox’s newest case, the Statement Series, is definitely an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or another flagship smartphones. It’s also one in the few OtterBox cases that put aesthetics first, having its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement right now, and we’ll decide if it should join our picks soon.
The Hard Candy Cases Candy Clip Series is a pretty crazy proposition: For $30, you receive a hard-plastic X-shaped piece that snaps onto the back of the iPhone, covering its corners and a few of the edges but leaving the buttons and many of the sides exposed. No thanks.
Urban Armor Gear’s Case is one of the only cases we’ve tested in order to meet military drop-test standards. It’s excellent as being a protective case, however its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in this instance, but instead of a glossy finish, it relies on a matte one, with an industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it looks like an issue that would not really out of place with a construction site. We all do take issue with the two small, rectangular holes on the back of the way it is-with regards to a quarter of how through the top or bottom, respectively, they expose portion of the logo and also the top 1 / 2 of “Phone” inside the iPhone label. It’s an unusual design decision by using an otherwise impressive case. On the flip side, this model does come with a screen film, whereas most iPhone cases don’t these days.
Tech21’s entire product lineup will depend on D3O, a certified material the company uses in each and every one of the cases. Mostly contained in the borders of Tech21 cases, the brilliant-orange material should really remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing problems for your phone. The corporation really likes to show off the stuff; every one of its cases is at least translucent, if not transparent, across the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. The first is the most basic, a glossy TPU skin that’s wider in comparison to the NGP, thanks to the layer of D3O. We’d like to visit a bigger lip than this example offers, along with the buttons are a bit squishier than we generally prefer. The Classic Shell Cover keeps the identical frame but replaces the TPU around the back by using a hard-plastic plate, and it has an attached cover to protect the iPhone’s display. The rest works just like with the standard model, and the lid includes a cutout on the earpiece in order to speak around the phone with it closed. The Classic Shell Flip is basically the same, only instead of plastic this example includes a leather feel (it appears to be the fake stuff), along with the lid comes around from the bottom as opposed to the side. We find that lids get in the way a lot more than they help, so neither of such covered models excites us, and the soft buttons and wider body of the Classic Shell prevent it from acquiring a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. The initial one is a basic silicone skin using a grid on the back that glows at nighttime. With regards to body coverage, the truth lives around what we’re trying to find, but making this type of design involves a low amount of difficulty. As we’ve often found with cases with this style previously, the vertical edges can pull outside the body of your phone more readily as compared to other cases, allowing dust along with other particulates to obtain underneath. The Gelato, alternatively, is iphone7 case with the attractive checkerboard pattern in the back. It looks and feels excellent, nevertheless the .33-millimeter lip is just too short.
Poetic’s Atmosphere can be a thin case made of dual-molded polycarbonate plastic and TPU. The softer material rings the top edge to create a small lip, and it likewise runs on the antenna breaks on the rear of the phone. Although this transparent case initially may seem like a good option for folks who want a slim protector but still want to demonstrate their iPhone, it falls short because of button protectors that need excessive force to press.
Macally shipped us a handful of different cases, but two are styles we simply can’t recommend. Both the Metallic Snap-On Case along with the Flexible Protective Frame come in a number of colors, although the former is a shell, and the latter is really a bumper that protects the sides but leaves the scratchable back exposed. The Durable Protective Case, in contrast, does offer more thorough protection, but unfortunately it isn’t a genuine design. A mixture TPU skin and hard-plastic frame, this case sort of seems like an armadillo from the back. We’ve already seen a minimum of one other company supplying the same case, and that we weren’t impressed with the case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, however it is one of the more original designs we’ve found in the pile. This two-piece case includes a front frame (black- and white-rimmed versions are contained in the package) as well as a silicone rubber and plastic back. You only snap the phone into the selection of frame after which insert it into the back piece, which include flip-open port protectors. The amount of protection this model offers to the pricing is impressive, as it includes a built-in screen film and Touch ID coverage. Nevertheless the latter ends up being the Alixo 6S’s downside: Even though the fingerprint sensor does assist the thin material over it, we found it to be less reliable, requiring more efforts to unlock these devices.
Marblue’s ToughTek is actually a thick silicone rubber case that is included with a screen protector. Basically we don’t doubt this thing will be able to tolerate some significant drops, the ToughTek is big-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to get in and from tight pockets as a result of grippy material. It may not be described as a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration in the CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, with all the latter material sticking up on top of the hard plastic. Probably the most intriguing thing about this case may be the pair of inch-long ridges, one on either sides. They’re made to use an array of accessories, such as a belt clip. We’ll be keeping an eye out for these accessories, and we’ll see whether they boost the price of the way it is.
We had high hopes for that Spigen Capella, which comes in multiple colors. Its setup is very similar to the CandyShell’s, with rubber inside and plastic outside. The large difference, and the reason we had been pumped up about it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This is certainly partly due to smaller, half-millimeter lip throughout the screen. One of our own editors loves just how the case’s slight curve feels, comparing it towards the iPhone 3G. Judging by the feedback we’ve seen from readers and Amazon reviewers, many people don’t like this shape up to perform.
Although the Capella isn’t as deep because the CandyShell, this is a bit taller, and about 3 mm wider. This width eventually ends up being problematic for 2 reasons, one on either edge. On the iPhone’s left side, the switch is quite a bit harder to toggle, as it’s deeply recessed inside the rubber border; if you don’t have nails to speak of, moving it to and fro will probably be tough. On the opposite side, the Sleep/Wake button requires a surprising amount of pressure to activate. If you’re willing to manage those drawbacks, the Capella is otherwise worth considering as being a CandyShell alternative.
Featuring its Revolution case, Poetic looks to contest with companies including OtterBox in a far lower price. The way it is begins with a plastic frame that snaps on the front of the iPhone; a specific sheet of plastic protects the screen while leaving the sensors at the very top as well as the Touch ID button at the end exposed. A rubber and plastic body fits throughout the back, snapping into position using the front piece. The whole thing feels quite sturdy, the buttons click well, and also the flap on the Lightning port is really a nice little extra protection.
Supcase’s Unicorn Beetle Pro Holster provides a similar proposition. The greatest distinction between this model along with the Revolution is that it features a plastic belt holster. Having roughly a similar dimensions because the Poetic case, this model requires an installation that’s basically the identical. This case adds a number of flaps for coverage, namely over the side switch and also the headphone port along with the Lightning port. While it’s an incredibly solid-feeling case, we immediately called the company’s claim of dust-proof construction into question, because it leaves openings for dust to get in, such as the fully exposed speaker. Presently, Amazon users are usually fond of it, with 127 reviews as well as a 4.1-star (out from five) rating, but we’ve seen several three- and four-star reviews.
Relative newcomer Supcase has a variety of iPhone 6 cases, actually, nearly all of that are section of the “Unicorn Beetle” family. The Slim Armored Protective Case is a lot like Urban Armor Gear’s case because it’s protective, nevertheless the design is rather specific, meaning it likely won’t entice exactly the same wide swath of folks as something a little more generic. The plastic and rubber case feels sturdy and contains a few of the clickiest buttons for any we tested. With regards to lip, it’s no more than .5 mm, so it’s smaller than we’d like, as well as the case makes no mil-spec claims. If you appreciate the appearance, it’s not necessarily a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a precise-plastic backplate by using a TPU bumper. That polycarbonate back won’t absorb just as much shock as being the thick rubber border, but it’s the best way to show off Apple’s design.
Within a previous version with this guide, we named Logitech’s Protection [ ] as a more-protective pick. It has a very similar design, with some great benefits of a matte finish and embedded magnets that allow it to connect to mounting accessories. Unfortunately Logitech has confirmed that it’s not any longer selling the case, which can be currently on clearance at Best Buy.
Not any other case we tested is set up the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like all kinds of other models, it uses both rubber and plastic components, but here the rubber is really a bumper that wraps across the iPhone’s border, as well as the plastic snaps in place over it while covering the back of the handset. In spite of the unusual design-or maybe for doing it-the situation offers superior protection compared to many more we’ve seen. It includes a 1-mm lip, plus speaker and Lightning-port protection. In addition, it redirects the audio ports forward, meaning the sound comes to you, as an alternative to down; the design has no influence on audio quality, thankfully. With regards to Lightning port, it stays protected underneath a rubber tab that one could flip out when you need access.
Few case manufacturers actively warn that the product doesn’t offer drop protection, however this kind of message appears on the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds virtually no bulk towards the handset, not really a protective lip. It’s a lot better than a shell since it offers button protection and cutouts for your ports, even when they are quite tight. But with this sort of warning from your case maker itself, we can’t recommend the Liquid Skin for many people. If you’re going to use a case, you may use something that’ll endure a drop.
Maxboost’s Crystal Cushion and that i-Blason’s Halo Series are almost identical to one another and might be small tweaks about the same reference design. Have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges will be more squared-off, whilst the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, although the lip across the screen is nearly nonexistent, especially in the Halo Series. Combine by investing in the tendency for clear plastic cases to scratch and to expose trapped dust underneath, which cases aren’t top picks.
The Maxboost HyperPro Series is perfect for all intents and purposes a thicker version from the Incipio NGP. Available only in black, it uses two layers of TPU to protect the iPhone, and yes it measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well and it also incorporates a protective lip, but we can find no real benefit to this situation on the NGP, other than savings of only a few dollars.
One of only a few slider-style cases out there, Maxboost’s Vibrance Series provides a different build than many of the cases we tested. A tough-plastic case, it splits into two pieces, both lined by using a soft fabric over the back that’s created to prevent damage during installation and removal. As an alternative to pushing the phone in to the case, you accomplish the bottom cap, slide the phone in to the top, and after that push the pieces back together again. Much much like the STM Harbour, this kind of design permits you to keep the iPhone thoroughly protected usually, and to plug it into docks when necessary. The lip is sort of short, though, and pulling away from the Vibrance’s bottom cap is harder than flipping within the Harbour’s bottom. Maxboost even offers only one color choice, salmon by using a gold cap, which might not entice several people as more basic colors would.
If you locate the CandyShell being too large, you won’t be impressed with Speck’s MightyShell, which can be found in black, orange, purple, pink, and clear variants. This model has a couple of key differences. First is definitely the extra layer of TPU material that assists absorb shocks to a greater degree; it adds 2 mm in width and height, in addition to .5 mm for the thickness of the case. Speck claims that it new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether this means the way it is is tested to survive drops from twice as high or it implies the way it is can tolerate the standard 4-foot drops twice as many times. One aspect of the case we appreciate is the hard-plastic exterior, which happens to be matte as an alternative to glossy, so that it won’t show scratches as readily as being the standard CandyShell. For that price, we expect not only claims of better drop protection; conditions in which this case would survive but a CandyShell wouldn’t are far too ambiguous to justify the fee.
Among ultrathin cases, Shumuri’s SLIM looks and feels nearly the same as Caudabe’s The Veil XT, as a result of the absence of the typical Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, along with thicker plastic for extra protection. However, we’re not fans of the aesthetics-since the case’s rigid plastic is thicker, the organization has added a tiny slit to every corner to create putting the way it is on the phone easier. The design is useful enough; we don’t like the actual way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases which can be slightly thicker than Caudabe’s The Veil. The first kind provides good coverage over the phone’s bottom edge but just has the particular faintest of a screen-protection lip. The latter has neither.
Amzer’s Crusta might not seem like an excellent value at $35 (iPhone 6) or $45 (iPhone 6 Plus) by this writing, nevertheless the package includes not only a simple case. The situation itself uses a two-piece snap-together design by using a rubber bumper and a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen having a plastic back, however, you will still see any dust, hair, or some other particulates that get under the glass. Amzer includes a second bit of glass to protect the phone’s screen. The truth ends up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, including the phone-but it’s one in the better cases we’ve seen from Amzer, an organization otherwise renowned for inexpensive, nondescript accessories.
NewerTech is well known more for computer accessories than smartphone add-ons, however the company does provide a type of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX boasts a thick layer of gel material that absorbs and evenly distributes shocks. The truth is fairly bulky, yet an opening on the rear of the situation to the phone’s Apple logo actually subtracts from your overall measure of protection. We like the NGP.
We now have varying levels of praise for three cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of which. This bulky rubber case feels more like an accessory for the kid’s toy than the usual smartphone. It may be an effective case if children frequently make use of your phone, but we suspect that many adults will prefer something slimmer.
We love the Survivor Core (for iPhone 6 and iPhone 6 Plus) and all of Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both enable the handset’s returning to show using a clear back panel. The former has rubber edges, as well as its rubber corners protrude a bit, helping cushion the iPhone against drops-but the outcome is that it’s just a little bigger than a traditional case. The All Clear Identity, on the other hand, has a transparent back with translucent-rubber edges. The trouble, as with every cases sporting a definite back, is that both cases show any gunk that gets below the plastic. For a few people, that could be a sufficient compromise within a case designed to let you visit your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity can be a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is a good replacement for our top pick, however it doesn’t quite make your top tier. The design is very similar to that from the Incipio NGP, as it’s a one-piece polyurethane case. The biggest difference is across the phone’s bottom edge: Instead of having separate openings to the headphone jack, microphone, Lightning-connector port, and speaker, the case exposes the past two through one long opening. A little indentation inside the plastic covering the base of the phone enables use with accessories including Apple’s Lightning-connector adapters. It is a nice feature we haven’t seen on other cases, although we worry that this thinness of the material here, in addition to nearby the Ring/Silent switch, will make it more vulnerable to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage to be somewhat problematic, because he doesn’t that way they’re nearly flush using the case.
Among the cases brought to us for consideration, we dismissed a number of models right from the start. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, in addition to Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, due to their Apple-logo-exposing holes in the back. They are doing a good job of protecting your phone otherwise, but we can easily think about no reason at all to recommend them for most of us when existing hole-free options are as good or better.
We also dismissed a variety of shell cases because, since we mention above, they provide a minimal level of coverage for the device’s body. Among they were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same thing goes for that Neo Hybrid EX, Spigen’s bumper case, that provides even less protection.